SW Calculator
Head Selection
Shaft Selection
Grip Selection
Additional Options
Reserved for future use
Head Measurements
Raw Shaft Measurements
965.2F12 = F12_inches × 25.4 (Convert inches to millimeters)
508.0F16 = F16_inches × 25.4
Convert inches to millimeters
Cut Shaft Measurements
939.8F17 = F17_inches × 25.4
Convert inches to millimeters
913.01F9 = F17 - B13 + B6
Cut Shaft Length = Cut Club Length - Hosel Length + Bore Depth
114.7584F6 = F14 - ((F12 - F9) × F20)
Shaft Mass = Raw Mass - ((Raw Length - Cut Shaft Length) × Mass per mm)
477.6212F3 = F9 - ((F14 × (F12 - F16)) - (F14 - F6) × ((F12 - F9)/2 + F9)) / F6
Balance Point based on shaft geometry and mass distribution
0.100434F18 = 2.5 / (0.98 × 25.4)
Constant calculated from formula
Grip Measurements
Other Measurements
Results
D7.5B22 = CHAR((ROUND((R12-R13)/10,0)+64)) & R13
Nominal Swing Weight using character encoding
D8.9B24 = CHAR((ROUND((T11-T12)/10,0)+64)) & T12
High tolerance Swing Weight
D6.1B25 = CHAR((ROUND((V11-V12)/10,0)+64)) & V12
Low tolerance Swing Weight
SW (Low)
D6.1
SW
D7.5
SW (High)
D8.9
Calculated Moment Values
Low
Nominal
High
160901.6V5 = (B9 + B11 + B17) × ((B3 + B4_low) + (F9 + F10_low) + (J6 + J7_low) - (B6 + B7_low) - T3)
Low tolerance club moment calculation
160901.6R5 = (B9 + B16) × (B3 + F9 + J6 - B6 - R3)
Nominal club moment calculation
160901.6T5 = (B9 + B10_tol + B18) × ((B3 + B4_high) + (F9 + F10_high) + (J6 + J7_high) - (B6 - B7_high) - T3)
High tolerance club moment calculation
14754.62V4 = (F6 + F7_low) × ((F3 + F4_low) + (J6 + J7_low) - T3)
Low tolerance shaft moment calculation
14754.62R4 = F6 × (F3 + J6 - R3)
Nominal shaft moment calculation
14754.62T4 = (F6 + F7_high) × ((F3 + F4_high) + (J6 + J7_high) - T3)
High tolerance shaft moment calculation
13112.75V6 = (J3 + J4_high) × (T3 - (J9 + J10_low))
Low tolerance grip moment calculation
13112.75R6 = J3 × (R3 - J9)
Nominal grip moment calculation
13112.75T6 = (J3 + J4) × (T3 - (J9 + J10_high))
High tolerance grip moment calculation
534.55R7 = N3 × (F9 + J6 - B6 - R3)
Ferrule moment calculation
534.55R7 = N3 × (F9 + J6 - B6 - R3)
Ferrule moment calculation
534.55R7 = N3 × (F9 + J6 - B6 - R3)
Ferrule moment calculation
434.244R8 = N6 × (F9 - (B6/2) - R3)
Glue moment calculation
434.244R8 = N6 × (F9 - (B6/2) - R3)
Glue moment calculation
434.244R8 = N6 × (F9 - (B6/2) - R3)
Glue moment calculation
306.705R9 = N9 × ((10.5/2) × 25.4)
Tape moment calculation
306.705R9 = N9 × ((10.5/2) × 25.4)
Tape moment calculation
306.705R9 = N9 × ((10.5/2) × 25.4)
Tape moment calculation
0R10 = N12 × (F9 + J6 - B6 - R3)
Tip plug moment calculation
0R10 = N12 × (F9 + J6 - B6 - R3)
Tip plug moment calculation
0R10 = N12 × (F9 + J6 - B6 - R3)
Tip plug moment calculation
458.9583V10 = (V4 + V5 - V6 + R7 + R8 - R9) / V3
Low tolerance total moment value
458.9583R11 = (R4 + R5 - R6 + R7 + R8 - R9 + R10) / R3
Nominal total moment value
458.9583T10 = (T4 + T5 - T6 + R7 + R8 - R9) / T3
High tolerance total moment value
355.6V3 = B20 × 25.4
Fulcrum in millimeters
355.6R3 = B20 × 25.4
Fulcrum in millimeters
355.6T3 = B20 × 25.4
Fulcrum in millimeters
0.282023Slope = 0.282023
Constant slope value for swing weight calculation
0.282023Slope = 0.282023
Constant slope value for swing weight calculation
0.282023Slope = 0.282023
Constant slope value for swing weight calculation
-81.9622Intercept = -81.9622
Constant intercept value for swing weight calculation
-81.9622Intercept = -81.9622
Constant intercept value for swing weight calculation
-81.9622Intercept = -81.9622
Constant intercept value for swing weight calculation
D6.1B25 = CHAR((ROUND((V11-V12)/10,0)+64)) & V12
Low tolerance swing weight
D7.5B22 = CHAR((ROUND((R12-R13)/10,0)+64)) & R13
Nominal swing weight
D8.9B24 = CHAR((ROUND((T11-T12)/10,0)+64)) & T12
High tolerance swing weight
Head Measurement Tolerances
Parameter
Tolerance (-)
Tolerance (+)
Head Weight (g)
Hosel Length (mm)
Bore Depth (mm)
CG-b (mm)
Rat Glue (g)
Shaft Measurement Tolerances
Parameter
Tolerance (-)
Tolerance (+)
Raw Mass (g)
Raw Length (in)
Raw Length (mm)
Raw Balance Point (in)
Raw Balance Point (mm)
Cut Club Length (mm)
Cut Shaft Length (mm)
Cut Shaft Mass (g)
Cut Balance Point (mm)
Grip & Component Tolerances
Parameter
Tolerance (-)
Tolerance (+)
Grip Weight (g)
Cap Thickness (mm)
CG from Butt Cap (mm)
Ferrule (g)
Glue (g)
Grip Tape (g)
Tip Plug (g)